Mac Magazin/MacEasy 19/Mac Magazin and MacEasy Magazine CD - Issue 19.iso/Online/LineShare 3.3.1/LineShare Scripts/Supra Fax1&ARA&Data

Text File | 1995-06-06 | 9KB | 430 lines

! Version 3.1.3
!
!$ Use this script with Supra modems (up to V.34)
!$ Supports: fax, ARA and regular data incoming calls.
!
!$ Make sure that *Class 1* fax software is installed
!
!$ A cable for hardware handshaking is required

^2 Speaker On:        = Enum("Never" = "0","During Connect" = "1", "Always"="2") "1"
^3 Speaker Volume:       = Enum("Low"="1","Medium"="2","High"="3") "2"
^4 Answer On:         = Enum("1 Ring"="1","2 Rings"="2","3 Rings"="3","5 Rings"="5","7 Rings"="7") "2"
^5 Port Speed:        = Enum("9600","19200","38400","57600") "19200"
^6 Handshake wires:   = Bool("Both"="&D0","CTS only"="&D2") "&D2"
^7 Fax Port Speed:      = Enum("Fixed (14.4 modems)"="F","Auto (28.8 modems)"="V") "F"
^8 Error Correction:  = Bool("Disabled"="&Q6","Enabled"="&Q5") "&Q6"
! ------------------------------------------
! Resetting the modem:
! ------------------------------------------
@Hangup
  SetTries 2
  Flush
  HsReset 0,0,17,19,0,0
  DtrSet
!
! Try to catch the "OK" answer, use the Escape seq and DTR transitions
! to enter the command mode
!
@Label 1
  matchclr
  matchstr 1 2 "OK\r\n"
  write "ATH0&F1\r"
  matchread 20
  ChrDelay 1
  Write "+++"
  ChrDelay 0
  DtrClear
  SBreak
  DtrSet
!
  DecTries
  IfTries 0 1
!
! OSErr -6019 "Modem error - the modem is not responding"
!
  exit -6019
@Label 2
  write "AT+FCLASS=0\r"
  Jsr 100
  write "AT+FAE=0\r"
  Jsr 100
  exit 0

! ------------------------------------------
!    Receiving incoming calls
! ------------------------------------------
@ANSWER
!
! Set the modem preferred speed first
!
  SerReset Val("^5"),0,8,1
  Jsr 80

@Label 10
!
! Set the common options
  Jsr 70
!
! Set the communication options:
! • &Q6/Q5: Error connection
! • &K3: HW flow control       (for ARA, Fax should not use a handshake on receiving)
! • W1:  report connection speed
!
  Write "AT^8&K3W1\r"
  Jsr 100
!
! Set Fax mode
!
  Write "AT+FCLASS=1\r"
  Jsr 100
  Write "AT+FAE=1\r"
  Jsr 100
!
! It's for Rockwell ONLY! Set FCLASS to 0 again - otherwise,
! it cannot accept data calls
!
  Write "AT+FCLASS=0\r"
  Jsr 100
!
! Tell the modem to determine the type of the incoming call
! Fetch the tube after ^4 rings
!
  Write "ATS0=^4V0\r"
  Jsr 110
!
! Everything is ready - let's sit and wait for a call
! We'll wait for 2 minutes, then reinitiate the modem
!
  Note "Waiting for a fax/ARA/data call…"
  MatchClr
  matchstr 02 40 "47\r"
  MatchStr 03 41 "48\r"
  MatchStr 04 42 "49\r"
  MatchStr 05 43 "50\r"
  MatchStr 06 44 "51\r"
  MatchStr 07 45 "52\r"
  MatchStr 08 46 "53\r"
  MatchStr 09 47 "54\r"
  MatchStr 10 48 "55\r"
  MatchStr 11 49 "56\r"
  MatchStr 12 50 "57\r"
  MatchStr 13 51 "58\r"

  MatchStr 14 45 "95\r"
  MatchStr 15 46 "96\r"
  MatchStr 16 47 "97\r"
  MatchStr 17 48 "98\r"
  MatchStr 18 49 "99\r"
  MatchStr 19 50 "100\r"
  MatchStr 20 51 "101\r"

  MatchStr 25 19 "33\r"
  matchstr 26 18 "2\r"
  matchstr 27 57 "1\r"
  matchstr 28 17 "3\r"
  matchstr 29 17 "8\r"
  matchstr 30 17 "7\r"
@Label 16
  Matchread 1200
@Label 17
  Note "Tuning again…"
  Write "ATV1\r"
  Jsr 100
  Jump 10
@Label 18
  Note "Ring…"
  Jump 16
@Label 19
  Note "Fax tones detected…"
  IfStr 7 16 "V"
  SetSpeed 19200
  Jump 16

!
! Data connection has been established (we read "CONNECT")
! Put the "CONNECT" back to the buffer and attach the "Data" subPort
! if it was an incoming call, put the "RING" before the "CONNECT"
!
@Label 20
  IfOpen "Data" 21
  Jump 30
@Label 21
  IfOpen "ARA" 22
  Jump 35
@Label 22
  Note "Waiting for an ARA frame"
  MatchClr
! MatchStr 1 23 "^$\r"    6/6/95: there are messages like 70\r still in the buffer.
  MatchStr 2 28 "\08\01\03\14\04\03\00\08\250\16\03"
  MatchStr 3 29 "\01\27\02\29\01\02\01\06"
  MatchRead 60
  Jump 24
@Label 23
  QueueInput "^$\r"
@Label 24
  Note "Non-ARA call"
  Jump 35

@Label 28
  Note "ARA 1.0 call"
  Jump 30
@Label 29
  Note "ARA 2.0 call"
  Jump 30

@Label 30
  QueueInput "\r\nCARRIER ^B\r\n"
  QueueInput "\r\nRING\r\n"
  Attach "ARA" (DTR)

@Label 35
  GetSReg C "DATA" 4
  QueueInput "\r^CCONNECT ^B\r^C"
  ifOriginate 36
  QueueInput "\r^CRING\r^C"
@Label 36
  Attach "Data" (DTR,Escape,Break)


!
! Converting numeric responses into the verbal
!
@Label 40
  SetVar B "2400"
  Jump 20
@Label 41
  SetVar B "4800"
  Jump 20
@Label 42
  SetVar B "7200"
  Jump 20
@Label 43
  SetVar B "9600"
  Jump 20
@Label 44
  SetVar B "12000"
  Jump 20
@Label 45
  SetVar B "14400"
  Jump 20
@Label 46
  SetVar B "16800"
  Jump 20
@Label 47
  SetVar B "19200"
  Jump 20
@Label 48
  SetVar B "21600"
  Jump 20
@Label 49
  SetVar B "24000"
  Jump 20
@Label 50
  SetVar B "26400"
  Jump 20
@Label 51
  SetVar B "28800"
  Jump 20

! ------------------------------------------
! Originating a call through the "ARA" subport
! ------------------------------------------
@ORIGINATE "ARA"
  SerReset Val("^5"),0,8,1
  Jsr 80
!
! Set the common options
!
  Jsr 70
!
! Set the Data mode:
! • &Q6:Normal connection (no compression, correction - for ARA)
! • &K3: HW Handshake
! • S7:  time-out (90 sec) for long-distance calls
! • W1:  report connection rate
!
  Write "AT&Q6&K3S7=90W1\r"
  Jsr 100
!
! Emit the ARA script commands ("Xnn")
  Jsr 60
!
! Prepare to receive all error result codes, dial the number
!
  Jsr 90
  MatchStr 1 55 "\r\nCARRIER ^$\r\n"
  MatchStr 2 55 "\r\nCARRIER ^$/VFC\r\n"
  MatchRead 1000
  Write "\r"
  Exit -6019
@Label 55
  QueueInput "\r\nCARRIER ^$\r\n"
  Attach "ARA" (DTR)

! ------------------------------------------
! Originating a call through the "DATA" subport
! ------------------------------------------
@ORIGINATE "Data"
  SerReset Val("^5"),0,8,1
  Jsr 80
!
! Set the common options
!
  Jsr 70
!
! Set the Data mode:
! • \N3: Auto-reliable
! • &K3: HW Handshake
! • S7:  time-out (90 sec) for long-distance calls
!
  Write "AT&K3S7=90\r"
  Jsr 100
!
! Emit the Data commands
  Jsr 60
!
! Prepare to receive all error result codes, dial the number
!
  Jsr 90
  MatchStr 1 56 "\r\nCONNECT "
  MatchRead 1000
  Write "\r"
  Exit -6019
@Label 56
  QueueInput "\r\nCONNECT "
  Attach "Data" (DTR,Escape,Break)

! ------------------------------------------
! Originating a call through the "Fax" subPort
! ------------------------------------------
@ORIGINATE "Fax"
!
! Set the "Fax" speed
!
  SerReset 19200,0,8,1
  Jsr 80
!
! Set the common options
!
  Jsr 70
!
! Set the Fax mode
! &K4: Xon/Xoff handshake
!
  Write "AT&K4+FCLASS=1\r"
  Jsr 100
!
! Now emit all commands that the application has sent to that port,
! except "FCLASS", etc
!
  EmitClear "+FCLASS","V","E"
  Jsr 60
  Write "ATV0\r"
  Jsr 110
!
! Prepare to receive all error result codes, dial the number
!
  MatchClr
  MatchStr 01 57 "1\r"
  MatchStr 13 93 "3\r"
  MatchStr 14 94 "8\r"
  MatchStr 15 92 "7\r"
  Write "ATD^1\r"
  HsReset *
  MatchRead 900
  Write "\r"
  Exit -6019

!
! Fax connection has been established (we read "FAX")
! Put the +FCON back to the buffer,
! if it was an incoming call, put the "RING" before the "+FCON"
! Attach the "Fax" subPort
!
@Label 57
  QueueInput "1\r"
  IfStr 7 58 "V"
  SetSpeed 19200
@Label 58
  ifOriginate 59
  QueueInput "2\r2\r"
@Label 59
  Attach "Fax" (Reset(2400),IdleLimit=30)

!
! This section emits all modem commands sent from the client application
! For each set of commands the "OK" answer is awaited
!
@Label 60
  EmitStart
@Label 61
  EmitCommand 62
  Jsr 100
  Jump 61
@Label 62
  return
!
! This section initiates the modem before ANSWER and ORIGINATEs:
! extended responses + connect at the highest rate + speaker control +
! reset on Dtr drop + DCD valid
! Verbal responses mode, no echo
!
@Label 70
  Write "ATX4N1M^2L^3^6&C1V1E0\r"
  Jsr 100
  return

!
! This section syncronize the modem after the serial port speed switching
!
@Label 80
  ChrDelay 1
  Write "AT\r"
  ChrDelay 0
  Jsr 100
  return
!
! Prepare to receive error result codes, send the dialing command and
! set the user's handshake mode
!
@Label 90
  MatchClr
  MatchStr 2 91 "NO DIALTONE\r\n"
  MatchStr 3 92 "BUSY\r\n"
  MatchStr 4 93 "NO CARRIER\r\n"
  MatchStr 5 94 "NO ANSWER\r\n"
  Write "ATD^1\r"
  HsReset *
  return
@Label 91
  exit -6020
@Label 92
  exit -6022
@Label 93
  exit -6021
@Label 94
  exit -6023
!
! Processing the AT command:
! OK -> proceed
! ERROR or TimeOut ->exit -6019
! It can be called AFTER the "Write" command, since LineShare buffers input
!
@Label 100
  MatchClr
  MatchStr 1 103 "\r\nOK\r\n"
  MatchStr 2 102 "\r\nERROR\r\n"
@Label 101
  MatchRead 20
@Label 102
  Exit -6019
@Label 103
  return

@Label 110
  MatchClr
  MatchStr 1 103 "0\r"
  MatchStr 2 102 "4\r"
  Jump 101